iFlight Nazgul Evoque F5 V2 FPV Frame Kit 5inch F5D F5X for FPV parts

Description

Description
nThe old days are over, getting your electronics full of dirt and wet grass every time you crash. Our latest frame reduces contamination that could build up on your flight controller or ESCs, preventing failure or short circuits. Strategic airflow to keep your components cool and clean without taking any shortcuts in weight or performance. Illuminated side panels and 360-degree TPU protective parts.
nHighlights
nV1 to V2 was upgraded for the DJI O3 HD Air Unit Digital Transmission
nSpecially Designed Heatsink for DJI O3 Air Unit
nNew Camera Mount for a wider camera FOV with TPU damping inserts
nNew Side Panels to perfectly fit the O3 Air Unit in the back
nNew Dual 5.8G VTX Antenna TPU mount
nLatest Nazgul Frame Upgrades for Maximum Protection
nOptional Parts to select (not included in frame kit):
n//www.aliexpress.com/item/1005005046578370.html?spm
nNew Anti Spark Filter to prevent rapid voltage and current spikes plugging in a battery
nSingle DJI VTX Antenna TPU to install the original DJI O3 set included antenna.
nUpgrading your Nazgul F5 V1?
nIf you want to upgrade your Nazgul Evoque F5 V1 with the DJI O3 Air Unit read this:
nThe FC (Flight Controller) to O3 VTX connector is different than the older Caddx Vista/Polar plug. You’ll need to DIY.
nThe RX (Receiver) position changed. V1 antenna length is 75mm, V2 is 220mm. You’ll need to DIY.
nThe XT60 plug was changed, you’ll need to de-solder the V1 plug and install the V2 plug. Included in the frame kit.
nIf you’re going from F5X V1 to F5X V2 all motor wires will have the same length.
nIf you’re going from F5X V1 to F5D V2 the back motor wires need to be extended, since you change frame geometry.
nThe Antenna TPU in the back comes in 2 Versions; One for the original single DJI VTX antenna, or one for the dual antenna setup. The kit includes a dual antenna TPU. 2x 5.8G LHCP antennas need to be installed.
nThe Nazgul Evoque F5 V2 BNF comes with a new Anti Spark filter pre-installed. Please select the option to purchase separately; it’s not included in the frame kit.
nSpecifications
nProduct Name：Evoque F5 V2 Frame Kit
nFrame wheelbase: 225mm (Squashed X) / 223 mm (DeadCat)
nFrame Dimension: L258*W199*H25 mm (Squashed X) / L190*W136*H36 mm (DeadCat)
nFrame Body Dimension: 36mm
nArm Thickness: 6mm
nBottom Plate Thickness: 3mm
nTop Plate Thickness: 2mm
nUpper Plate Thickness: 3mm
nCamera Plate Thickness: 3mm
nMotor Mounting：16x16mm
nVTX Mounting：25.5*25.5/Φ1.6mm
nWeight: 150grams (Included no TPU Parts)
nNOTE: Due to manufacturing processes, the thickness of our products may have a standard manufacturing tolerance of ±0.2mm. The size of the hole may have a standard manufacturing tolerance of ±0.1mm.
nPacking List
n1 x Evoque F5 V2 Frame Kit
n1x O3 Air Unit Heatsink
n2x O3 IPEX to RP-SMA Antenna Pigtails
n1 x O3 Dual Antenna TPU
n1 x GoPro TPU Base Mount
n1 x Screw Bag
n4 x TPU Armguard
n1 x Front Bumper TPU
n1 x Rear Bumper TPU
n2 x Anti-slip Battery Pad
n2 x Battery Strap (20*250mm)